 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| ZeroIC PCS/CDMA 3.4V/28dBm Linear Power Amplifier Module TM AWT6332 Data Sheet - Rev 2.1 * * * * * * * * * FEATURES InGaP HBT Technology High Efficiency: 37 % @ +28 dBm output Zero Quiescent Current in Switch Mode Internal Voltage Regulation Optimized for a 50 System Low Profile Surface Mount Package: 1 mm CDMA 1XRTT, 1xEV-DO Compliant RoHS-Compliant Package, 250 oC MSL-3 CDMA/EVDO PCS-band Wireless Handsets and Data Devices APPLICATIONS M27 Package 10 Pin 3 mm x 3 mm x 1 mm Surface Mount Module RF switch mode, current consumption is less than 10 A, reducing the average current consumption 70% more than a HELP2TM PA over the CDG profile. Its integrated voltage regulator eliminates the need for external components further reducing size and BOM cost. The 3 mm x 3 mm x 1 mm surface mount package incorporates matching networks optimized for output power, efficiency, and linearity in a 50 system. PRODUCT DESCRIPTION The AWT6332 is a new product in the revolutionary ZeroICTM PA family. The AWT6332 uses ANADIGICS' exclusive InGaP-PlusTM technology, which combines HBT and pHEMT devices on the same die, to enable state-of-the-art reliability, temperature stability, and ruggedness. The AWT6332 has a unique architecture with two RF inputs. One input drives the power amplifier while the other input drives an RF switch that bypasses the power amplifier, going directly to the RF output. The mode control logic selects the PA or the RF switch. In Figure 1: Block Diagram 09/2008 AWT6332 Figure 2: Pinout (X-ray Top View) Table 1: Pin Description PIN 1 2 3 4 5 6 7 8 9 10 NAME VBATT RFIN_SWITCH RFIN_PA VMODE VEN GND GND RFOUT VCC VCC DESCRIPTION Battery Voltage RF Input to Switch RF Input to PA Mode Control Voltage PA Enable Voltage Ground Ground RF Output Supply Voltage Supply Voltage 2 Data Sheet - Rev 2.1 09/2008 AWT6332 ELECTRICAL CHARACTERISTICS Table 2: Absolute Minimum and Maximum Ratings PARAMETER Supply Voltage (VCC and VBATT) Mode Control Voltage (VMODE) Enable Voltage (VEN) RF Input Power (PIN) to PA RF Input Power (PIN) to Switch Storage Temperature (TSTG) MIN 0 0 0 -40 MAX +5 +3.5 +3.5 +10 +20 +150 UNIT V V V dBm dBm C Stresses in excess of the absolute ratings may cause permanent damage. Functional operation is not implied under these conditions. Exposure to absolute ratings for extended periods of time may adversely affect reliability. Table 3: Operating Ranges PARAMETER Operating Frequency (f) Supply Voltage (VCC and VBATT) Enable Voltage (VEN) Mode Control Voltage (VMODE) RF Output Power (POUT) Case Temperature (TC) MIN 1850 +3.2 +2.2 0 +2.2 0 27.5 -30 (1) TYP +3.4 +2.4 +2.4 +28.0 - MAX 1915 +4.2 +3.1 +0.5 +3.1 +0.5 +85 UNIT MHz V V V dBm C COMMENTS PA "on", Switch "on" PA "shut down" PA Mode Switch Mode The device may be operated safely over these conditions; however, parametric performance is guaranteed only over the conditions defined in the electrical specifications. Notes: (1) For operation at VCC = +3.2 V, POUT is derated by 0.5 dB. Data Sheet - Rev 2.1 09/2008 3 AWT6332 Table 4: Electrical Specifications - CDMA Operation (IS-95 Modulation) (TC = +25 C, VBATT = VCC = +3.4 V, VEN = +2.4 V, 50 system) PARAMETER Gain Insertion Loss Adjacent Channel Power at +1.25 MHz offset Primary Channel BW - 1.23 MHz Adjacent Channel BW = 30 kHz Adjacent Channel Power at +2.25 MHz offset Primary Channel BW - 1.23 MHz Adjacent Channel BW = 30 kHz Isolation Power-Added Efficiency Enable Current Mode Control Current MIN 24.5 TYP 27 0.8 MAX 29.5 1.5 UNIT dB COMMENTS POUT = +28 dBm, VMODE = +2.4 V VMODE = 0 V - -51 -70 -46.5 - dBc POUT = +28 dBm, VMODE = +2.4 V VMODE = 0 V 31 34.5 - -59.5 -70 34 37 <0.1 <0.01 <10 <10 -136 -40 -45 - -56.5 0.25 0.1 15 dBc dB % mA mA POUT = +28 dBm, VMODE = +2.4 V VMODE = 0 V RFOUT to RFIN_SWITCH, VMODE = +2.4 V, PA "on" POUT = +28 dBm, VMODE = +2.4 V through VEN pin, VEN = +2.4 V through VMODE pin, VMODE = +2.4 V VCC = +4.2 V, VEN = 0 V, VMODE = 0 V or +2.4 V VCC = +4.2 V, VEN = +2.4 V, VMODE = 0 V, Switch Mode Leakage Current Noise in Receive Band Harmonics 2fo 3fo, 4fo Input Impedance Spurious Output Level (all spurious outputs) Load mismatch stress with no permanent degradation or failure 18 -134 -30 -30 2:1 A dBm/Hz 1930 MHz to 1990 MHz CW Measurement dBc VSWR - - -65 dBc POUT < +28 dBm In-band load VSWR < 5:1 Out-of-band load VSWR < 10:1 Applies over all operating ranges Applies over full operating range 8:1 - - VSWR Notes: (1) PAE and ACP limit applies at 1880 MHz (IS-95 modulation). 4 Data Sheet - Rev 2.1 09/2008 AWT6332 APPLICATION INFORMATION To ensure proper performance, refer to all related Application Notes on the ANADIGICS web site: http://www.anadigics.com Shutdown Mode The power amplifier may be placed in a shutdown mode by applying a logic low levels (see Operating Ranges table) to both the VEN and VMODE voltages. Power Modes The power amplifier may be placed in either a Low Power mode or a High Power mode by applying the appropriate logic level (see Operating Ranges table) to the VMODE voltage. The Power Control table lists the recommended modes of operation for various applications. Table 5: Power Control APPLICATION CDMA - Switch Bypass Shutdown CDMA - PA Shutdown POUT LEVELS -* -* All POWER MODE Low Low High Shutdown VEN +2.4 V 0V +2.4 V 0V VMODE 0V +2.4 V +2.4 V 0V *Dependent upon typical output power of Transceiver and phone board design. Figure 3: Application Circuit Data Sheet - Rev 2.1 09/2008 5 AWT6332 PACKAGE OUTLINE Figure 4: M27 Package Outline - 10 Pin 3 mm x 3 mm x 1 mm Surface Mount Module Figure 5: Branding Specification 6 Data Sheet - Rev 2.1 09/2008 AWT6332 COMPONENT PACKAGING Figure 6: Tape & Reel Packaging Table 6: Tape & Reel Dimensions PACKAGE TYPE 3 mm x 3 mm x 1 mm TAPE WIDTH 12 mm POCKET PITCH 4 mm REEL CAPACITY 2500 MAX REEL DIA 7" Data Sheet - Rev 2.1 09/2008 7 AWT6332 ORDERING INFORMATION ORDER NUMBER TEMPERATURE RANGE -30 C to +85 C PACKAGE DESCRIPTION COMPONENT PACKAGING AWT6332RM27Q7 RoHS-Compliant 10 Pin 3 mm x 3 mm x 1 mm Tape and Reel, 2500 pieces per Reel Surface Mount Module RoHS-Compliant 10 Pin 3 mm x 3 mm x 1 mm Partial Tape and Reel Surface Mount Module AWT6332RM27P9 -30 C to +85 C ANADIGICS, Inc. 141 Mount Bethel Road Warren, New Jersey 07059, U.S.A. Tel: +1 (908) 668-5000 Fax: +1 (908) 668-5132 URL: http://www.anadigics.com E-mail: Mktg@anadigics.com IMPORTANT NOTICE ANADIGICS, Inc. reserves the right to make changes to its products or to discontinue any product at any time without notice. The product specifications contained in Advanced Product Information sheets and Preliminary Data Sheets are subject to change prior to a product's formal introduction. Information in Data Sheets have been carefully checked and are assumed to be reliable; however, ANADIGICS assumes no responsibilities for inaccuracies. ANADIGICS strongly urges customers to verify that the information they are using is current before placing orders. ANADIGICS products are not intended for use in life support appliances, devices or systems. Use of an ANADIGICS product in any such application without written consent is prohibited. WARNING 8 Data Sheet - Rev 2.1 09/2008 |
Price & Availability of AWT6332RM27P9
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |